Dry contact monitoring · Cellular

Know the moment a relay trips at your remote site.

Wire any dry contact (a pump fault relay, float switch, generator alarm or door switch) to the Hygge Monitor. When it changes state, your team gets a text and email over cellular, with no Wi-Fi, no SCADA and no site visit.

Cellular planIncluded
Power lossBattery backup
AlertsUp to 5 people

Most remote equipment already says when something is wrong. Nobody is there to hear it.

Pumps, generators, HVAC units and alarm panels have fault or run relays built in. Out at a lift station, well house or equipment shelter, that signal often goes nowhere until someone drives out on a route check, or a customer calls.

The Hygge Monitor turns any of those relay outputs into a text message, using its own cellular connection. There's no network to configure at the site and no SCADA integration to pay for.

How it works

Set up in an afternoon.

01

Wire the contact

Connect the two wires from your equipment's dry contact output to the monitor's Leak port. The monitor reads it the same way it reads a water leak.

02

Plug in and power on

The monitor finds a cellular signal on its own, usually within 90 seconds. A solid blue light means it's connected.

03

Add your team

Scan the QR code to register the device at iot.hyggeapps.com, name the site, and add up to 5 people to get text and email alerts.

What you can monitor

If it has a relay output or a switch, you can get a text or email about it.

A dry contact is a plain switch with no voltage of its own, so it's either open or closed. Most industrial equipment has one for faults, run status or alarms.

Pump and lift stations

Pump fail and overload relays, high-level float switches, and control panel alarm outputs.

Backup generators

Generator running, fail-to-start, and transfer switch position contacts.

Tanks and wells

High and low level float switches on water, fuel and chemical tanks.

Doors, gates and hatches

Magnetic reed switches on shelter doors, cabinet enclosures and access hatches.

HVAC and cooling

Common alarm and fault relays on rooftop units, CRAC units and shelter air conditioners.

Alarm and control panels

Spare relay outputs on fire, security or PLC panels that aren't connected to a monitoring service.

Monitor any dry contact: wire in pumps, generators, float switches and door sensors to the Hygge monitor's leak port and get an instant alert when a contact closes.
Wiring

Two wires. That's the whole install.

Run a two-conductor cable from the equipment's dry contact terminals to the monitor's Leak port. When the contact closes, the monitor sees the circuit complete and sends an alert.

  • Use a voltage-free (dry) contact only. Never connect a powered or wet output to the monitor.
  • Wire to the equipment's normally open (NO) terminals so the contact closes on a fault.
Wiring diagram
Equipment relay COM NO
Hygge H3 LEAK port Contact closed = alert
Contact openNormal, no alert
Contact closedText + email sent

One device covers the whole site, not just the relay.

The same monitor watching your contact also keeps track of the shelter it's mounted in.

Power failure alerts

Know within about a minute when outlet power drops. The internal battery keeps the monitor reporting.

Temperature and humidity

Set your own high and low limits and get alerted when the shelter gets too hot, too cold or too damp.

Cellular built in

Each monitor comes with its own cellular plan. No Wi-Fi, router or separate carrier contract needed.

Hourly readings

Check conditions anytime in the Hygge portal, with a fresh reading every hour.

Specifications

ModelHygge Monitor H3
Contact inputLeak port, dry (voltage-free) contact
ConnectivityCellular, connects automatically; plan included
AlertsSMS and email, up to 5 users
Also monitorsTemperature, humidity, outlet power
Power5 V DC via USB-C (120 V wall adapter included); internal backup battery
Operating range0°F to 120°F (−18°C to 49°C), 0–100% RH non-condensing
InstallationIndoors only, such as inside a shelter, pump house or building

Questions

What is a dry contact?

A dry contact is a switch or relay output that carries no voltage of its own. It just opens or closes a circuit. Float switches, door reed switches and most equipment "alarm" or "fault" relay terminals are dry contacts.

Does it work where there's no Wi-Fi or internet?

Yes. The monitor uses its own cellular connection, and the plan is included. All the site needs is a standard outlet and cellular coverage.

What happens if the site loses power?

You get a power failure alert, and the internal battery keeps the monitor running so it can keep reporting.

Can it be installed outdoors?

No. Mount the monitor indoors, inside the building, shelter or pump house, and run the contact wires to it from the equipment.

Best for dry contacts

Monitor + Dry Contact Cable

The Hygge monitor with a dry contact cable for the Leak port, plus 1 year of cellular service. Temperature, humidity and power alerts included.

$142 Select

Stop finding out on the next route check.